The town of Red Oak has seen more than its fair share of shootouts and gunfights. Its location in the Arizona territory seems to be within the reach of many of the varied groups who hope to gain some sway over the people of the West. The bridge in town is the only one for miles up and downstream and could be considered a strategic point for anyone with military learning. Wyatt Earp passes through, sometimes dropping off his latest quary in the Jail until they can be properly tried. The Metalsmith in town is usually tasked with fixing some broken piece of equipment or other that most rough-and-tumble types don't have the smarts to look after properly. Various Outlaw gangs end up in town wanting to trade or spend their ill-gotten gains on whatever entertainment their minds can think up. The Cathouse and Saloon are usually the first place Outlaws (or anyone new in town for that matter) head to. If trouble starts in either of these places the locals usually make sure the instigators are sent to the last place in town anyone wants to visit, the Crematorium. It's an unusual site but the local Boot Hill was filled to bursting during the Ore War so most of the locals have got used to the foul-smelling smoke on Sunday afternoons. The one place that isn't busy is the Prospector's Shack just on the outskirts. Some say it's haunted and some say that Old Joshua just likes to keep to himself with the aid of a shotgun. Either way, most folks keep their distance.

Please note: Scenery items are manufactured in Medium Density Fibre Board (MDF). Buildings are supplied primed and some assembly will be required. Assembly instructions can be found online and by scanning the QR printed on the packaging.

This set contains;

• 1x Crematorium
• 1x Cat House
• 1x Saloon
• 1x Bridge
• 1x Jail
• 1x Scatter
• 1x Metalsmith
• 1x Prospector's Shack

The Drill is a well-known and valuable tool for the converter and modeler. Drill holes in metal, resin and plastic miniatures with the drill bits provided. Drill fits up to 3mm bits.

Contents:

• 1.0mm bit
• 1.4mm bit
• 1.8mm bit

Bob Smith Industries Insta-Cure. CyanoAcrylate Super Glue, for ceramics, plastics, and hardwoods. 5-10 sec drying glue, 1 oz bottle. Reaches full strength in 2 hours.

Bob Smith Industries Insta-Cure. CyanoAcrylate Super Glue, for ceramics, plastics, and hardwoods. 5-10 sec drying glue, 1 oz bottle. Reaches full strength in 2 hours.

Bob Smith Industries Insta-Set. CyanoAcrylate Super Glue Accelerator, compatible with all surfaces including plastic and foam. 8-10 sec cure time, 2 oz spray bottle.

Bob Smith Industries Insta-Set. CyanoAcrylate Super Glue Accelerator, compatible with all surfaces including plastic and foam. 8-10 sec cure time. Refill for spray bottle.

Bob Smith Industries Un-Cure. CyanoAcrylate Debonder glue remover. Takes 20-120 seconds, 1 oz bottle. Removes CA glue, paint, and adhesive residue from models, tools, and skin.

Mission Models Color Change is delivers a subtle color change side cast and highlight effect. The pigment is suspended in a clear carrier and can be sprayed over any base coat. We suggest experimenting to find the desired effect. The possibilities are endless.

Use Mission Models Polyurethane Mix Additive with any Mission Models Paint for improved flow, leveling, and adhesion to any surface.

1 oz water based acrylic black primer. Must be thinned with Mission Models Thinner only. No substitutions.

Our high grade acrylic thinner is a very powerful formula. When mixing your paint we recommend a ratio of 20-30% to 1or in other words 2 to 3 drops to 10 drops of paint. Same ratio for our Primer. These are the ideal ratios for perfect results. Over thinning will cause more transparency in the paint. Once you mix paint to our recommended ratio you can then further mix to suit your needs.

Our thinner is also your airbrush cleaner.

Tamiya X-23 Clear Blue Acrylic Paint 23ml

Tamiya X-24 Clear Yellow Acrylic Paint 23ml

Tamiya X-25 Clear Green Acrylic Paint 23ml

Tamiya X-26 Clear Orange Acrylic Paint 23ml

Tamiya X-27 Clear Red Acrylic Paint 23ml

TTCombat Double Sided, gridded miniature and MDF Self Healing Cutting Mat. A3 size, 3mm thick with markings for miniature base sizes on one side and measurements on both sides.

This pack contains 50 x N52 grade neodymium magnets. Small but extremely strong, these are great for gluing into models in order to keep customisation.

Perfect for rearming your Dropfleet space ships or changing up your special weapons on your Popular Space Soldier miniatures, look no further!

These magnets are 1mm diameter and 1mm thick. You get approximately 50 per pack, all of the same size. Exact contents may vary.